|
Пас- порт:
|
APP N° 727
|
Thickness measurement of thermal insulation panels
The thickness of thermal insulation panels should be measured INLINE.
|
|
|
Пас- порт:
|
APP N° 698
|
Distance measurement to insulation panels
The distance to insulation panels should be measured.
|
|
|
Пас- порт:
|
APP N° 681
|
Color and intensity control of filament lamps
The color as well as the intensity of filaments lamps should be controlled.
|
|
APP N° 587
Param.:
|
|
Moisture control of bricks
The moisture of bricks should be controlled.
|
|
APP N° 586
Param.:
|
|
Moisture control of clinker bricks
The moisture of clinker bricks should be controlled.
|
|
APP N° 585
Param.:
|
|
Moisture control of concrete blocks
The moisture of concrete blocks should be controlled.
|
|
APP N° 584
Param.:
|
|
Moisture of gas concrete
The moisture of gas concrete should be controlled.
|
|
|
Пас- порт:
|
APP N° 527
|
Gloss differentiation of coated flagstones from uncoated flagstones
Coated flagstones should be differentiated from uncoated flagstones.
|
|
|
Пас- порт:
|
APP N° 522
Param.:
|
|
Color measurement of glazed tiles
The color of glazed tiles should be inline measured.
|
|
|
Пас- порт:
|
APP N° 503
Param.:
|
|
Stone plate thickness control
The thickness of stone plates should be measured. At this, the stone plates will be transported on a conveyor belt with a negligible movement in height, thus it can be used as a reference.
|
|
|
Пас- порт:
|
APP N° 490
|
Thickness measurement of polished slabs
The thickness of polished slabs should be measured. It should be noted, that the slabs are placed on a reference plate.
|
|
|
Пас- порт:
|
APP N° 489
Param.:
|
|
Gloss measurement on polished slabs
The gloss of polished slabs should be measured.
|
|
|
Пас- порт:
|
APP N° 488
|
Color control of polished slabs
The color of polished slabs should be controlled.
|
|
|
Пас- порт:
|
APP N° 470
|
Roof tile color measurement
The color of roof tiles should be inline measured.
|
|
|
Пас- порт:
|
APP N° 453
Param.:
|
INI:
|
|
Measurement of the length of gypsum plasterboard
The length of gypsum plasterboard should be measured.
|
|
|
Пас- порт:
|
APP N° 346
|
Color control of T-grids for ceiling systems
T-grids used for ceiling systems should be color controlled.
|
|
|
Пас- порт:
|
APP N° 333
|
Frequency control of industrial ventilators
Ventilators for industrial purposes should be frequency checked. Furthermore the direction of rotation should be controlled.
|
|
|
Пас- порт:
|
APP N° 294
|
Thickness control of shiny aluminum cushions
The thickness of different shiny aluminum cushions should be measured. These aluminum cushions are used for heat insulation. At this, the cushions will be transported on a conveyor belt with a very small fluctuation in height, thus the distance to the belt can be used as a reference.
|
|
|
Пас- порт:
|
APP N° 289
|
Evenness control of angle grinder discs
The flatness of angle grinder discs should be controlled during the rotation.
|
|
|
Пас- порт:
|
APP N° 149
|
Differentiation between water moistened and dry floor tiles
After the moisturization the floor tiles should be checked, whether the amount of moisture is in the right range or out of range (too much or too little moisture content). The tiles looks brighter if the degree of moisture is too small and the tiles looks darker as normal if too much water is on the tiles. In the normal case the tiles looks gray in color.
|
|
|
Пас- порт:
|
APP N° 144
|
Position monitoring of tiles
The orientation of tiles on a conveyor belt should be controlled. There are three chamfers which splits the tile into four parts and these chamfers should be perpendicular orientated on the conveyor belt.
|
|
|
Пас- порт:
|
APP N° 134
|
Control of the presence of fibers in an aluminum tube
In aluminum tubes with a length of approximately 160mm and an inner diameter of 14mm the presence of fibers should be checked, at which a good tube is a tube without any fibers. The tubes can be positioned and turned 360° around, around both ends of the tube there is space enough for mounting the sensors.
|
|
|
Пас- порт:
|
APP N° 105
|
Övervakning av spraymunstycke Kontroll av att spraymunstycket inte är igensatt och att rätt mängd vätska kommer ur munstycket.
Spray jet amount control
The density of the spray jet should be controlled.
|
|
|
Пас- порт:
|
APP N° 88
|
Fluorescent glue control on an abrasive belt
During the production of abrasive belt material with a 10mm wide glue stripe the presence of the fluorescent glue must be observed. Defects greater than 2mm in length must be proper detected. The distance of the sensor head to the object should be approximately 20mm and the detecting range around 2mm x 10mm.
|
|
|
Пас- порт:
|
APP N° 87
|
Kontinuerlig glansmätning på slipband Glansen är ett mått på strävheten på slipband. En glansgivare monteras i produktionsprocessen och ger kontinuerlig mätning.
Inline gloss measurement on abrasive belts
The gloss factor is a significant parameter for the surface quality, the roughness, of an abrasive belt. Thus a gloss measurement inline sensor should be used for quality control of the abrasive surface.
|
|
|
Пас- порт:
|
APP N° 77
|
Edge control of abrasive belts
The edges of abrasive belts must be grinded to a certain degree. Thus, the degree of grinding should be controlled.
|
|
|
Пас- порт:
|
APP N° 57
|
Detection of a fluorescent line on different colored foamed materials
A fluorescent line must be detected on different colored foamed materials.
|
|
|
Пас- порт:
|
APP N° 51
|
Kontroll av kantlinje på slipband På slipband finns en linje vid ytterkanten av slipytan. Denna linje ska detekteras och den skiljer sig i färg mot slipytan och det rena bandet. Oftast är den mörkare än bandet men ljusare än slipytan vilket gör att givaren kan detektera den smala linjen.
Control of margined abrasive belts
Different sanding belts are equipped with a margin and this margin has to be controlled. The margin can be present on the sanding side of the abrasive belt or on the rear side. Furthermore the margin can be darker than the rear side but mostly it is brighter than the sanding surface. Nevertheless there is a sufficient difference in contrast between the margin and the rear side or the sanding side.
|
|