|
Data sheet:
|
APP N° 794
|
Presence control of a very thin oil layer
The presence of a very thin oil layer (< 1µm) should be controlled.
|
|
|
Data sheet:
|
APP N° 711
Param.:
|
|
Color checking of the paintwork through sight glasses
The color of liquid lacquers should be controlled in using sight glasses. It should be taken into account, that the sight glasses have a reflecting surface.
|
|
|
Data sheet:
|
APP N° 673
|
Spray jet control with a laser through beam system
The amount of liquid and the geometry of a spray jet next to the spray nozzle should be controlled.
|
|
APP N° 626
|
Intensity control of fluorescent additives in oil-soaked paper
The intensity of fluorescent additives in oil-soaked paper should be controlled.
|
|
|
Data sheet:
|
APP N° 598
Param.:
|
INI:
|
|
Color control of flames
The color of a flame should be controlled.
|
|
|
Data sheet:
|
APP N° 517
Param.:
|
INI:
|
|
Concentration control of a passivator in a solvent
The amount of a passivator in a solvent should be controlled.
|
|
|
Data sheet:
|
APP N° 459
Param.:
|
INI:
|
|
Plastic ring bottom side – upper side differentiation
Plastic rings which are transported on a conveyor belt should be differentiated with a view to the direction (bottom side – upper side).
|
|
|
Data sheet:
|
APP N° 458
Param.:
|
INI:
|
|
Cut off point detection on a fleece tape
The cut off line on a fleece tape should be detected. It should be taken into account, that the fleece tape as well as the cut off line is white in color, thus, there is no color difference.
|
|
|
Data sheet:
|
APP N° 457
|
Position detection of a silicon layer on a transparent plastic film
The position of a silicon layer on a transparent plastic film should be detected (frontside / backside differentiation).
|
|
|
Data sheet:
|
APP N° 213
|
Detection of the presence of foam on a liquid
The presence of the foam on a liquid should be detected. Furthermore the liquid level (+ foam, if present) should be measured simultaneously.
|
|
|
Data sheet:
|
APP N° 195
|
Color differentiation of fluorescent oil
Different oil types which are used for engines should be differentiated. At this, the natural effect of UV fluorescence of mineral oil is used. Furthermore fluorescent liquid will be added to some of the mineral oils, which allows a differentiation of the adequate types.
|
|
|
Data sheet:
|
APP N° 126
|
Color control of lacquers
The lacquer should be inline controlled. At this a special casing is used which will be plunged into the lacquer.
|
|
|
Data sheet:
|
APP N° 111
|
Drop control with a laser through beam system
The number as well as the volume of drops should be controlled.
|
|
|
Data sheet:
|
APP N° 55
|
Color control of an emulsion
The color of the emulsion which should be controlled is normally white but it can happen that the color is drifting slightly into the red or the green range. This drift must be controlled.
|
|
|
Data sheet:
|
APP N° 23
|
Kontrola barve tekočin Kontrola tekočin npr. vode med proizvodnjo oz. procesiranjem le-te je nujno potrebna, ker lahko pride vsled onesnaženja do spremembe barve le-te, npr. rahlo modrikasta je lahko posledica onesznaženja (polucije) ali nežno bež barva je lahko posledica prosotnosti olja itd. V obeh primerih je potrebna kontrola barve vode, ki mora biti brezbarvna in prosojna.
Colored liquid control
During a water cycle process the quality of the water must be controlled. It can happen that the water becomes slightly blue (pollution) or beige (oily) in color. Both case must be detected, the water must be clean.
|
|